313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 embedded power for business-critical continuity nfs110 series single & quad output special features ? 7.0 x 4.25 x 1.8 inch package ? overvoltage and short circuit protection ? 110 w with 20 cfm ? adjustable outputs ? en55022, en55011 conducted emissions level b ? ul, vde and csa safety approvals ? ce mark ? available rohs compliant ? 2 year warranty total power: 80 - 110 w input voltage: 85 - 264 vac 120 - 370 vdc # of outputs: single, quad safety vde0805/en60950/ iec950/iec1010 file no. 10401-3336-0213 licence no. 4001467 7 ul1950 file no. e132002 csa c22.2 no. 950 file no. lr41062c ? ? ? ? ? rev. 06.30.09_69 nfs110 series 1 of 5 electrical specifcations all specifcations are typical at nominal input, full load at 25 c unless otherwise stated output voltage adjustability: +5.1 v o/p on multi-s 5.1 v single output 12 v single output 15 v single output 24 v single output 3.0% 3.0% 12 - 14 v 15 - 18 v 24 - 30 v line regulation: ll to hl, fl all outputs on all units 0.1% max. overshoot/undershoot: at turn-on 0% temperature coeffcient: all outputs 0.02%/c overvoltage protection: multi o/p 5.1 v only 5.1 v single output 12 v single output 15 v single output 24 v single output 6.25 v 0.75 v 6.25 v 0.75 v 15.75 v 1.0 v 22 v 1.5 v 33 v 2.5 v output power limit: primary power limited pin max. 160 w pout min. 110 w minimum output current: (see note 13) 0 a short circuit protection: burst mode operation input input voltage range: 85 - 264 vac 120 - 370 vdc input frequency range: 47 - 440 hz input surge current: 230 vac 35 a safety ground leakage current: 110 vac, 50 hz 230 vac, 50 hz 0.2 ma, max. 0.4 ma, max.
rev. 06.30.09_69 nfs110 series of 5 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 environmental specifcations thermal performance: operating ambient 0 c to +70 c (see notes 9, 10) non-operating -40 c to +85 c 0 c to 50 c convection cooled 80 w +50 c to +70 c, convection cooled derate 2 w/c 0 c to +50 c, 20 cfm forced air 110 w +50 c to +70 c, 20cfm forced air derate 2.75 w/c peak, 0 c to +50 c, max. 60 seconds 110w relative humidity: non-condensing 5 to 95% rh altitude: operating 10,000 feet max. non-operating 40,000 feet max. vibration: (see note 11) 5 - 500 hz 2.4 g rms peak emc characteristics conducted emissions: en55022, fcc part 15 level b radiated emissions: en55022, fcc part 15 level a esd air: en61000-4-2, level 3 perf. criteria 1 esd contact: en61000-4-2, level 4 perf. criteria 1 surge: en61000-4-3, level 3 perf. criteria 1 fast transients: en61000-4-4, level 3 perf. criteria 1 radiated immunity: en61000-4-5, level 3 perf. criteria 2 conducted immunity: en61000-4-6, level 3 perf. criteria 1 general specifcations hold-up time: 110 vac @ 80 w 110 vac @ 110 w 230 vac @ 80 w 230 vac @ 100 w 35 ms 17 ms 140 ms 100 ms effciency: multiple outputs +5.1 v single 12 v and 15 v singles 24 v single 70% typical 70% typical 72% typical 75% typical isolation voltage: input/output input/chassis 3000 vac 1500 vac approvals and standards: (see note 12) vde0805, en60950, iec950, iec1010, ul1950, csa c22.2 no. 950 weight: singles multiple outputs 550 g (19.4 oz) 600 g (21.2 oz) mtbf (@25 o c): mil-hdbk-217e 125,000 hours min.
rev. 06.30.09_69 nfs110 series 3 of 5 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 notes 1 convection cooled, 80 w maximum. 2 peak outputs lasting less than 60 seconds with duty cycle less than 10%. total peak power must not exceed 110 w. 3 forced air, 20 cfm at 1 atmosphere, 110 w maximum. 4 figure is peak-to-peak. output ripple is measured across a 50 mhz bandwidth using a 12 inch twisted pair terminated with a 47 f capacitor. 5 total regulation is defned as the static output regulation at 25 c, including initial tolerance, line voltage within stated limits and output voltages adjusted to their factory settings. 6 to achieve stated regulation on the 24 v output on the nfs110-7602pj, the following load condition must be true: i a / i b 5, where: i a = +5.1 v output current, and i b = +24 v output current the +24 v output will maintain 5.0% regulation under the following additional condition: i a 5 a. 7 single output models have foating outputs which may be referenced as either positive or negative. higher voltage supplies may be adjusted over a wide output voltage range, as long as the total output power does not exceed 80 watts (natural convection) or 110 watts (forced air). 8 power fail detect not available on single output models. 9 derating curve is application specifc for ambient temperatures >50 c, for optimum reliability no part of the heatsink should exceed 90 oc and no semiconductor case temperature should exceed 100 oc. 10 caution: allow a minimum of 1 second after disconnecting the power when making thermal measurements. 11 three orthogonal axes, random vibration, 10 minute test for each axis. 12 this product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 13 artesyn technologies recommends a minimum load of 11 w to achieve the design mtbf. see the derating curve on page 3. 14 the j- suffx indicates that these parts are pb-free (rohs 6/6) compliant. 15 notice: some models do not support all options. please contact your local emerson network power representative or use the on-line model number search tool at http://www.powerconversion.com to fnd a suitable alternative. ordering information output voltage output currents ripple (4) total regulation (5) mo? el nu??ers o? el nu??ers (13, 14, f) max (1) peak (2) fan (3) +5.1 v 8 a 20 a 10 a 50 mv 2.0% NFS110-7601PJ +12 v 4.5 a 9 a 5 a 120 mv 3.0% C12 v 0.5 a 1.5 a 1 a 120 mv 3.0% C5 v 0.5 a 1.5 a 1 a 50 mv 3.0% +5.1 v (i a ) 8 a 20 a 10 a 50 mv 2.0% nfs110-7602pj (6) +24 v (i b ) (6) 3.5 a 4.5 a 4.5 a 240 mv +10/C5.0% +12 v 4.5 a 9 a 5 a 120 mv 3.0% C12 v 0.5 a 1.5 a 1 a 120 mv 3.0% +5.1 v 8 a 20 a 10 a 50 mv 2.0% nfs110-7604pj 15 v 4 a 7.5 a 5 a 150 mv 4.0% -15 v 0.5 a 1.5 a 1 a 150 mv 3.0% -5 v 0.5 a 1.5 a 1 a 50 mv 3.0% 12 v 7 a 9 a 9 a 120 mv 2.0% nfs110-7612j (7,8) 15 v 5 a 7.3 a 7.3 a 150 mv 2.0% nfs110-7615j (7,8) 24 v 3.5 a 4.5 a 4.5 a 240 mv 2.0% nfs110-7624j (7,8) transient response NFS110-7601PJ +5.1 v (7.5 a to 10 a) +12 v (2.5 a to 5 a) -12 v (0.5 a to 1 a) -5 v (0.5 a to 1 a) 150 mv peak, 1 ms recovery 100 mv peak, 0.5 ms recovery 100 mv peak, 0.5 ms recovery 100 mv peak, 0.5 ms recovery nfs110-7602pj +5.1 v (7.5 a to 10 a) +24 v (1.5 a to 3 a) +12 v (2.5 a to 5 a) -12 v (0.5 a to 1 a) 150 mv peak, 1 ms recovery 300 mv peak, 1 ms recovery 100 mv peak, 0.5 ms recovery 100 mv peak, 0.5 ms recovery nfs110-7604pj +5.1 v (7.5 a to 10 a) +15 v (2.5 a to 5 a) -15 v (0.5 a to 1 a) -5 v (0.5 a to 1 a) 150 mv peak, 1 ms recovery 100 mv peak, 0.5 ms recovery 100 mv peak, 0.5 ms recovery 100 mv peak, 0.5 ms recovery nfs110-7605j +5.1 v (10 a to 20 a) 250 mv peak, 1 ms recovery nfs110-7612j: +12 v (4.5 a to 9 a) 360 mv peak, 1 ms recovery nfs110-7615j +15 v (3.65 a to 7.3 a) 450 mv peak, 1 ms recovery nfs110-7624j +24 v (2.25 a to 4.5 a) 720 mv peak, 1 ms recovery
all dimensions in inches (mm) optional powe r fail de tect circuit (key = pin 2) pin 1 6-32 unc (4pl) pin 1 1.00 0.005 (25.4) voltage adjust j2 j1 f1 l1 t1 c6 pin 1 0.156 dia . hole (4pl) 5a, 250 vac 0.475 0.010 (12.07) 1.55 0.005 (39.37) 3.35 0.015 (85.09) 1.80 (45.72) max 0.050 0.020 (1.27) 4.250 0.020 (107.95) 3.750 0.005 (95.25) 0.250 0.010 (6.35) 0.250 0.010 (6.35) 6.50 0.005 (165.1) 7.00 0.020 (177.8) t1 rev. 06.30.09_69 nfs110 series of 5 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 ac (j1) mating connector molex 09-50-3051 or molex 09-91-0500 mating connector with 2478 or equivalent crimp terminals. dc (j2) mating connector molex 09-50-3131 or molex 09-91-1300 mating connector with 2478 or equivalent crimp terminals. power fail detect signal (note 8) 50ms t1 200ms t2 will vary with line and load t3 3ms pout: 110w pfd output is an open collector which will sink 40ma in the low state. hig h t1 t2 t3 4.75v 3.5v min 0-0.4 max low 4.75v 5v output pfd signal ac input optional power f ail detect timing diagram 80w 20 cfm forced air cooling 40w 55w 0w 11w 11w minimum load required at 230vac na tural convection cooling 0c 10c 20c 30c 40c 50c 60c 70c dera ting curve (see notes 9, 10) output powe r (watts) 110w pin connections j1 -7601pj -7602 p -7604pj singles pin 1 ac ground ac ground ac ground ac ground pin 2 ac neutral ac neutral ac neutral ac neutral pin 3 ac line ac line ac line ac line j2 pin 1 +5.1 v +5.1 v +5.1 v v out pin 2 +5.1 v +5.1 v +5.1 v v out pin 3 +5.1 v +5.1 v +5.1 v v out pin 4 return return return return pin 5 return return return return pin 6 return return return return pin 7 return return return return pin 8 +12 v +12 v +15 v v out pin 9 +12 v +12 v +15 v v out pin 10 pfd pfd pfd n/c pin 11 -12 v -12 v -15 v n/c pin 12 removed for key pin 13 -5 v +24 v -5 v n/c n/c = no connection mechanical notes: a metallic or non-metallic stand-offs (maximum diameter 5.4mm) can be used in all four mounting holes without effecting safety approval. b the ground pad of the mounting hole near j1, allows system grounding through a metal stand-off to the system chassis. c the heat sink is grounded, and allows system grounding by mechanical connection to the system chassis. d the supply must be mechanically supported using the pcb mounting holes and may be additionally supported by the heatsink mounting holes. e it is always advisable to attach the power supply heat sink to another thermal dissipator (such as a chassis or fnned heatsink etc). the resulting decrease in heat sink mounted component temperatures will improve power supply lifetime. f a standard l-bracket and cover is available for mounting which contains all screws, connectors and necessary mounting hardware. the kit is available, order part number nfs110cj.
313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 embedded power for business-critical continuity rev. 06.30.09_69 nfs110 series 5 of 5 a?ericas 5810 van allen way carlsbad, ca 92008 usa telephone: +1 760 930 4600 facsimile: +1 760 930 0698 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom telephone: +44 (0) 1384 842 211 facsimile: +44 (0) 1384 843 355 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong telephone: +852 2176 3333 facsimile: +852 2176 3888 for global contact, visit: www.powerconversion.co? techsupport.e??e??e?power @e?erson.co? while every precaution has been taken to ensure accuracy and completeness in this literature, emerson network power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. emerson network power and the emerson network power logo are trademarks and service marks of emerson electric co. ?2009 emerson electric co. e?ersonnetworkpower.co? embedded computing e??e??e? power monitoring outside plant power switching & controls precision cooling racks & integrated cabinets services surge protection e? erson network power. the global leader in enabling business-critical continuity. ac power connectivity dc power
|
